Cornel Accessories & Mounting Options Products
Showing 1 to 10 of 10 products
Frequently Asked Questions
Why are specific Stud Wall Brackets required for installing Cornel Column Radiators on partition walls?
Standard radiator brackets are often designed for solid masonry and may not align correctly with the timber uprights inside a plasterboard stud wall. The Stud Wall Bracket Kit provided for the Cornel range is technically engineered to offer a wider fixing area or specific alignment options. This ensures that the heavy weight of the steel column radiator is securely anchored into the wooden studs rather than just the plasterboard, preventing structural damage and ensuring safety.
What is the technical difference between Floor Mount Kits and Slip On Feet for these radiators?
The Floor Mount Kit is a structural support system designed to bolt the radiator securely to the floor, often used when walls are too weak to bear the weight. They raise the radiator by approximately 105mm. In contrast, Slip On Feet are largely decorative accessories that slide onto the bottom of the columns to create a traditional cast iron look, raising the height by 100mm. While feet support weight, they typically still require wall brackets or stays to prevent the radiator from tipping forward.
How does adding Floor Mounts or Feet affect the pipe work and pipe center dimensions?
Installing Cornel Floor Mounts or Slip On Feet lifts the radiator off the ground by roughly 100mm to 105mm. This technical elevation changes the vertical position of the pipe connections relative to the floor. You must account for this additional height when roughing in your copper pipework to ensure your radiator valves align perfectly with the inlets, avoiding the need for unsightly pipe alterations later in the installation process.
How do I determine if I need the Two Mount or Four Mount Floor Kit for my Cornel radiator?
The selection of the Floor Mount Kit depends strictly on the length and weight of your radiator, determined by its section count. For Cornel radiators with up to 21 sections, the Two Mount Kit is structurally sufficient. However, for longer radiators containing between 22 and 40 sections, the Four Mount Kit is required to prevent the middle of the radiator from sagging and to distribute the substantial weight evenly across the floor surface.
Can the mounting accessories be finished to match the specific colour of my Cornel radiator?
Yes, all mounting accessories, including Stud Wall Brackets, Floor Mounts, and Slip On Feet, can be customized to match your radiator. While the standard finish is White RAL 9016, you can order them in any S4H RAL Colour or Special Finish. This ensures a seamless aesthetic integration, although choosing a custom finish will typically align the delivery lead time with that of the bespoke radiator rather than the stock white items.
What is the purpose of the Nylon Spanner listed in the accessories section?
The Nylon Spanner is a specialized installation tool designed to tighten the chrome air vents and blanking plugs without damaging the finish. Standard metal spanners can easily chip or scratch the powder coated paint or chrome plating during tightening. Using this non abrasive tool ensures the aesthetic integrity of your Cornel Column Radiator is maintained during the final fit out, preserving the protective coating and the manufacturer warranty.
Are there restrictions on installing Towel Bars onto Cornel Column Radiators?
Yes, the Towel Bars are designed to clamp onto the columns of the radiator, and their length dictates a minimum size requirement. You need a radiator with at least 8 sections to fit the smaller towel bar, and at least 10 sections for the larger version. This ensures there is sufficient width for the bar to attach securely between the vertical tubes without interfering with the end sections or the wall brackets.
Why is it recommended to use a Stud Wall Bracket Kit for radiators requiring 6 brackets?
Large Cornel Column Radiators are extremely heavy when filled with water. A standard fixing setup might not provide enough points of contact on a hollow wall. The Stud Wall Bracket Kit for radiators requiring 6 brackets provides additional anchoring points. This distributes the sheer load more effectively across multiple studs, reducing the stress on any single point and eliminating the risk of the radiator pulling away from the wall over time.
Does the 10 Year Guarantee cover the mounting accessories as well as the radiator?
Yes, the Supplies4Heat Cornel mounting options and accessories, including brackets and feet, are covered by the same 10 Year Guarantee as the radiators themselves. This warranty covers manufacturing defects such as structural failure of the mounts or degradation of the finish. However, it is contingent upon the accessories being installed correctly according to the instructions and not being subjected to loads exceeding their design capacity.
When should I purchase Replacement Radiator Gaskets for my installation?
Replacement Radiator Gaskets are technical seals used between the steel sections or at the connection points for plugs and bushes. You generally do not need these for a standard new installation as the radiator comes assembled. However, if you are extending an existing Cornel radiator by adding sections, or if you have removed a plug for maintenance and the original seal is damaged, a fresh gasket is essential to ensure a watertight seal and prevent leaks in your central heating system.