Shaftsbury 540 Cast Iron Radiator Products
Showing 1 to 20 of 28 products
Frequently Asked Questions
How do I accurately calculate the total installation width for the Paladin Shaftsbury Cast Iron Radiator 540mm High model including the necessary allowances for radiator valves and pipework connections?
To calculate the exact installation width you must take the listed width of the cast iron sections and add the dimension of your chosen radiator valves. The widths shown on the product page such as 1242mm for the 13 section model refer only to the radiator body. You typically need to add approximately 90mm in total to this length which accounts for the valve bodies on both the flow and return sides. This ensures your pipe centers are positioned correctly before the radiator arrives.
Considering the significant weight of the Shaftsbury Cast Iron Radiator which can exceed 100kg does this product require specific structural reinforcement for suspended timber floors during installation?
The Shaftsbury 540mm High is a substantial unit with a depth of 155mm making it heavier than standard panel radiators. A 20 section model weighs roughly 142kg. If you are installing this on a ground floor with a concrete base no reinforcement is needed. However for suspended timber floors upstairs you should technically locate the joists and position the radiator feet directly over them where possible. If the feet land between joists using a load spreading board under the floorboards is a recommended technical solution to prevent sagging.
What is the technical significance of the Delta T 50C rating listed for the BTU output and how does it affect the heating efficiency if I use a modern condensing boiler or heat pump?
The BTU output listed such as 2750 BTUs for 10 sections is calculated at Delta T 50C which assumes a boiler flow temperature of roughly 75C. If you are using a modern condensing boiler or heat pump that runs at lower temperatures your Delta T will be lower resulting in less heat output. To solve this problem you should technically oversize the radiator by roughly 10 to 20 percent or use a correction factor calculation to ensure the Shaftsbury 540mm provides enough warmth for your room at lower water temperatures.
Why are Wall Stays strongly recommended for the Shaftsbury Cast Iron Radiator range and what is the technical procedure for installing them correctly to ensure safety?
Although the Shaftsbury radiator stands on its own feet Wall Stays are a critical safety device required to prevent the heavy radiator from tipping forward if knocked. Technically you should install one wall stay for radiators up to 10 sections and two or more for longer models. The stay clamps between the cast iron sections near the top and anchors firmly into the solid masonry or timber stud behind. This does not take the weight of the radiator but provides essential lateral stability.
Can I install the Paladin Shaftsbury 540mm High radiator on a one pipe heating system or does it strictly require a standard two pipe flow and return configuration?
While it is technically possible to install cast iron radiators on a one pipe system it is often inefficient due to the high water volume and flow resistance of the wide 155mm Shaftsbury sections. A modern two pipe system where hot water is pumped in one side and exits the other is the recommended technical setup. This ensures the 540mm high sections heat up evenly from top to bottom. If you must use a one pipe system you will need specialist high flow valves to ensure adequate circulation.
What is the difference between the Primer Black and Primer White finish options versus the Heritage Metallic Finishes in terms of on site preparation and long term durability?
The Primer Black and Primer White options are technically just transit coats intended to protect the iron from rust during storage and shipping. They are not a final finish. If you buy a Primer model you must paint it on site with a suitable metal paint to seal it. The Heritage Metallic Finishes are professionally applied factory finishes that are fully cured and ready for installation immediately. The factory finish offers superior durability against heat cycling compared to a standard DIY paint job.
How does the 155mm depth of the Shaftsbury Cast Iron Radiator affect the pipe center measurement from the finished wall surface for the first fix plumbing?
The Shaftsbury is a deep radiator at 155mm which means your pipework must be brought out further from the wall than for a standard radiator. To calculate the pipe center from the wall you generally take half the radiator depth which is 77.5mm and add the distance you want the back of the radiator to sit from the wall usually roughly 20mm to 30mm for skirting clearance. This means your pipes should technically come out of the floor approximately 100mm to 110mm from the finished wall surface.
Does the ornate floral design of the Shaftsbury collection trap dust and what is the recommended technical method for cleaning the cast iron sections without damaging the finish?
The ornate detailed casting of the Shaftsbury can collect dust within the scrolls. To maintain the heat output efficiency and appearance you should use a soft bristle brush or a vacuum with a soft attachment to remove dust from between the sections. Do not use wet cloths or abrasive chemical cleaners especially on Heritage Metallic Finishes or Hand Polished surfaces as this can technically degrade the lacquer seal leading to oxidation or rust spots over time.
If I order a large 20 section Shaftsbury Cast Iron Radiator will it be delivered fully assembled or will I need to join the sections together on site using a radiator assembly tool?
Paladin radiators from Budget Radiators are typically delivered fully assembled up to a certain length based on pallet weight limits. A 20 section Shaftsbury weighing 142kg will usually arrive on a pallet fully joined and pressure tested. You will need a strong team of at least 2 to 3 people to lift it off the pallet and into position. You do not technically need an assembly tool for standard orders unless you requested the radiator to be split for easier access to upper floors.
What specific type of radiator valves should I purchase to ensure compatibility with the 1 half inch BSP bush connections on the Shaftsbury 540mm High model?
The Shaftsbury 540mm High radiator comes with standard 1 half inch BSP bushes which is the universal thread size for UK radiator valves. You should technically choose Angled Valves if your pipes rise from the floor or Corner Valves if your pipes emerge from the wall. Straight valves are generally not suitable unless your pipes run horizontally along the skirting. Ensure you choose heavy duty brass valves that match the aesthetic and weight of the cast iron body.